QDMA Linux Driver UseCases¶

QDMA IP is released with five example designs in the Vivado® Design Suite. They are

AXI4 Memory Mapped And AXI-Stream with Completion
AXI Memory Mapped
AXI Memory Mapped with Completion
AXI Stream with Completion
AXI Stream Loopback
Descriptor Bypass In/Out Loopback

Note: AXI Memory Mapped with Completion is not supported.

Refer to QDMA_Product_Guide for more details on these example designs.

The driver functionality remains same for all the example designs. For Descriptor Bypass In/Out Loopback example design, application has to enable the bypass mode in driver.

All the flows described below are with respect to QDMA internal mode of operation. Also, the changes required in driver for bypass mode of operation are specified.

AXI4 Memory Mapped And AXI-Stream with Completion¶

This is the default example design used to test the MM and ST functionality using QDMA driver. This example design provides blocks to interface with the AXI4 Memory Mapped and AXI4-Stream interfaces. This example design covers most of the functionality provided by QDMA.

Refer to QDMA Product Guide for more details on the example design and its registers.

Below sections describes C2H and H2C data flow for ST and MM mode required in all the example designs.

MM H2C(Host-to-Card)¶

This Example Design provides BRAM with AXI-MM interface to achieve the MM H2C functionality. The driver comes with dma-ctl and dma-to-device applications which helps to realize the MM H2C functionality. QDMA driver takes care of HW updates.

The complete flow between the Host components and HW components is depicted in below sequence diagram.

Application needs to configure the queue to start in MM mode and H2C direction
dma-to-device command takes a file containing the contents to be transmitted to FPGA memory as input
Pass the buffer to be transferred as an input to dma-to-device application which in turn passes it to the QDMA Driver
QDMA driver divides buffer as 4KB chunks for each descriptor and programs the descriptors with buffer base address and updates the H2C ring PIDX
Upon H2C ring PIDX update, DMA engine fetches the descriptors and passes them to H2C MM Engine for processing
H2C MM Engine reads the buffer contents from the Host and writes to the BRAM
Upon transfer completion, DMA Engine updates the CIDX in H2C ring completion status and generates interrupt if required. In poll mode, QDMA driver polls on CIDX update.
QDMA driver processes the completion status and sends the response back to the application

For MM (H2C and C2H) bypass mode, application needs to enable the bypass mode on the required queues. Application can enable C2H/H2C bypass mode while starting the queue using dma-ctl application by specifying desc_bypass_en flag .

The MM descriptor format used by the example design is defined in QDMA Driver code base at linux-kernel/libqdma/descq.c

struct qdma_mm_desc {
        /** source address */
        __be64 src_addr;
        /** flags */
        __be32 flag_len;
        /** reserved 32 bits */
        __be32 rsvd0;
        /** destination address */
        __be64 dst_addr;
        /** reserved 64 bits */
        __be64 rsvd1;
};

Update this structure if any changes required in the descriptor format for bypass mode. Accordingly, update the data flow functionality in descq_mm_proc_request() functions in linux-kernel/libqdma/descq.c.

MM C2H(Card-to-Host)¶

This Example Design provides BRAM with AXI-MM interface to achieve the MM C2H functionality. The current driver with dma-ctl tool and dma-from-device application helps achieve the MM C2H functionality and QDMA driver takes care of HW updates.

The complete flow between the Host components and HW components is depicted in below sequence diagram.

User needs to start the queue in MM mode and C2H direction
Pass the buffer to copy the data as an input to dma-from-device application which inturn passes it to the QDMA Driver
QDMA driver programs the required descriptors based on the length of the required buffer in multiples of 4KB chunks and programs the descriptors with buffer base address and updates the C2H ring PIDX
Upon C2H ring PIDX update, DMA engine fetches the descriptors and passes them to C2H MM Engine for processing
C2H MM Engine reads the BRAM contents writes to the Host buffers
Upon transfer completion, DMA Engine updates the PIDX in C2H ring completion status and generates interrupt if required. In poll mode, QDMA driver polls on PIDX update.
QDMA driver processes the completion status and sends the response back to the application with the data received.

ST H2C(Host-to-Card)¶

In ST H2C, data is moved from Host to Device through H2C stream engine.The H2C stream engine moves data from the Host to the H2C Stream interface. The engine is responsible for breaking up DMA reads to MRRS size, guaranteeing the space for completions, and also makes sure completions are reordered to ensure H2C stream data is delivered to user logic in-order.The engine has sufficient buffering for up to 256 DMA reads and up to 32 KB of data. DMA fetches the data and aligns to the first byte to transfer on the AXI4 interface side. This allows every descriptor to have random offset and random length. The total length of all descriptors put to gather must be less than 64 KB.

There is no dependency on user logic for this use case.

The complete flow between the Host components and HW components is depicted in below sequence diagram.

User needs to start the queue in ST mode and H2C direction
Pass the buffer to be transferred as an input to dma-to-device application which in turn passes it to the QDMA Driver
QDMA driver divides buffer as 4KB chunks for each descriptor and programs the descriptors with buffer base address and updates the H2C ring PIDX
Upon H2C ring PIDX update, DMA engine fetches the descriptors and passes them to H2C Stream Engine for processing
H2C Stream Engine reads the buffer contents from the Host buffers the data
Upon transfer completion, DMA Engine updates the CIDX in H2C ring completion status and generates interrupt if required. In poll mode, QDMA driver polls on CIDX update.
QDMA driver processes the completion status and sends the response back to the application

For ST H2C bypass mode, application needs to enable the bypass mode on the required queues. Application can enable H2C bypass mode while starting the queue using dma-ctl application by specifying desc_bypass_en flag .

The ST H2C descriptor format used by the example design is defined in QDMA Driver code base at linux-kernel/libqdma/descq.c

struct qdma_h2c_desc {
        __be16 cdh_flags;       /**< cdh flags */
        __be16 pld_len;         /**< current packet length */
        __be16 len;             /**< total packet length */
        __be16 flags;           /**< descriptor flags */
        __be64 src_addr;        /**< source address */
};

Update this structure if any changes required in the descriptor format for bypass mode. Accordingly, update the data flow functionality in descq_proc_st_h2c_request () functions in linux-kernel/libqdma/descq.c.

ST C2H(Card-to-Host)¶

In ST C2H, data is moved from DMA Device to Host through C2H Stream Engine.

The C2H streaming engine is responsible for receiving data from the user logic and writing to the Host memory address provided by the C2H descriptor for a given Queue. The C2H Stream Engine, DMA writes the stream packets to the Host memory into the descriptors provided by the Host QDMA driver through the C2H descriptor queue.

The C2H engine has two major blocks to accomplish C2H streaming DMA,

Descriptor Prefetch Cache (PFCH)
C2H-ST DMA Write Engine

QDMA Driver needs to program the prefetch context along with the per queue context to achieve the ST C2H functionality.

The Prefetch Engine is responsible for calculating the number of descriptors needed for the DMA that is writing the packet. The buffer size is fixed per queue basis. For internal and cached bypass mode, the prefetch module can fetch up to 512 descriptors for a maximum of 64 different queues at any given time.

The Completion Engine is used to write to the Completion queues.When used with a DMA engine, the completion is used by the driver to determine how many bytes of data were transferred with every packet. This allows the driver to reclaim the descriptors.

PFCH cache has three main modes, on a per queue basis, called

Simple Bypass Mode
Internal Cache Mode
Cached Bypass Mode

While starting the queue in ST C2H mode using dma-ctl tool, user has the configuration options to configure the queue in any of these 3 modes.

The complete flow between the Host components and HW components is depicted in below sequence diagram.

The current ST C2H functionality implemented in QDMA driver is tightly coupled with the Example Design. Though the completion entry descriptor as per PG is fully configurable, this Example Design mandates to have the the color, error and desc_used bits in the first nibble. The completion entry format is defined in QDMA Driver code base libqdma/qdma_st_c2h.c

struct cmpl_info {
/* cmpl entry stat bits */
union {
        u8 fbits;
        struct cmpl_flag {
                u8 format:1;
                u8 color:1;
                u8 err:1;
                u8 desc_used:1;
                u8 eot:1;
                u8 filler:3;
        } f;
};
u8 rsvd;
u16 len;
/* for tracking */
unsigned int pidx;
__be64 *entry;
};

Completion entry is processed in parse_cmpl_entry() function which is part of libqdma/qdma_st_c2h.c. If a different example design is opted, the QDMA driver code in libqdma/qdma_st_c2h.h and libqdma/qdma_st_c2h.c shall be updated to suit to the new example design.

The ST C2H descriptor format described above shall be changed as per example design requirements.

Update this structure if any changes required in the descriptor format for bypass mode.

Accordingly, update the data flow functionality in descq_process_completion_st_c2h () functions in linux-kernel/libqdma/qdma_st_c2h.c.