# KV260 BIST Board Setup
## Hardware Requirements
1. KV260 Vision AI Starter Kit
2. KV260 Power Supply & Adapter
3. MicroSD Card
4. Host Machine (Windows or Ubuntu)
5. Four USB Flash Drives
6. One Ethernet Cable
7. One [PMOD TPH2 Test Point Headers](https://digilent.com/reference/pmod/pmodtph2/)
8. Four Female to Female Jumper Wires
9. One [Raspberry Pi Camera Module](https://www.raspberrypi.com/products/camera-module-v2/)
10. Two [Ar1335 Camera Sensors](https://www.xilinx.com/products/som/kria/kv260-vision-starter-kit/basic-accessory-pack.html)
11. 1080P/4K Monitor and Power Supply
12. DisplayPort/HDMI Cable
## Board Setup
This page shows how to set up the KV260 before running the BIST application.
Refer to the KV260 Board and the Interface layout below for connector reference numbers:
Test case mapping to board interfaces:
| Interface | External Hardware | Test Module | Test Case |
|------------------------------------|-----------------------------------------------------------|-------------|--------------------------|
| USB3.0 (Top port) - U44 | USB Flash Drive | Disk | usb1_read_performance |
| USB3.0 (Top port) - U44 | USB Flash Drive | Disk | usb1_write_performance |
| USB3.0 (Bottom port) - U44 | USB Flash Drive | Disk | usb2_read_performance |
| USB3.0 (Bottom port) - U44 | USB Flash Drive | Disk | usb2_write_performance |
| USB3.0 (Top port) - U46 | USB Flash Drive | Disk | usb3_read_performance |
| USB3.0 (Top port) - U46 | USB Flash Drive | Disk | usb3_write_performance |
| USB3.0 (Bottom port) - U46 | USB Flash Drive | Disk | usb4_read_performance |
| USB3.0 (Bottom port) - U46 | USB Flash Drive | Disk | usb4_write_performance |
| MicroSD port - J11 | MicroSD Card | Disk | sd_read_performance |
| MicroSD port - J11 | MicroSD Card | Disk | sd_write_performance |
| HDMI - J5 and/or Display Port - J6 | 1080p/4k Monitor and Power Cable, Display Port/HDMI Cable | Display | display_connectivity |
| HDMI - J5 and/or Display Port - J6 | 1080p/4k Monitor and Power Cable, Display Port/HDMI Cable | Display | display_modetest |
| SOM EEPROM | None | EEPROM | som_eeprom |
| Carrier Card EEPROM | None | EEPROM | carrier_card_eeprom |
| RJ45 Ethernet - J10 | Ethernet Cable | Ethernet | ethernet1_ping |
| RJ45 Ethernet - J10 | Ethernet Cable | Ethernet | ethernet1_perf |
| PMOD - J2 | PMOD TPH2 Test Header, 4x Female-Female Jumper Wires | GPIO | pmod0 |
| PS I2C Main Bus | None | I2C | ps_i2c_bus_main |
| AXI I2C Main Bus | None | I2C | axi_i2c_bus_main |
| AXI I2C Channel 0 Bus | None | I2C | axi_i2c_bus_ch0 |
| INA260 | None | IIO | ina260_current |
| QSPI MTD Device | None | MTD | qspi_read_write |
| QSPI MTD Device | None | MTD | qspi_read_performance |
| QSPI MTD Device | None | MTD | qspi_write_performance |
| PWM Fan - J13 | Board Fan | PWM | fan |
| TPM Hardware | None | TPM | tpm2_getcap |
| TPM Hardware | None | TPM | tpm2_selftest |
| TPM Hardware | None | TPM | tpm2_getrandom |
| TPM Hardware | None | TPM | tpm2_hash |
| TPM Hardware | None | TPM | tpm2_pcrread |
| TPM Hardware | None | TPM | tpm2_pcrextend |
| TPM Hardware | None | TPM | tpm2_pcrreset |
| IAS Connector - J7 & AP1302 | AR1335 Sensor | Video | ar1335_ap1302_ximagesink |
| IAS Connector - J7 & AP1302 | AR1335 Sensor | Video | ar1335_ap1302_perf |
| IAS Connector - J7 & AP1302 | AR1335 Sensor | Video | tpg_ap1302_ximagesink |
| IAS Connector - J7 & AP1302 | AR1335 Sensor | Video | tpg_ap1302_perf |
| Raspberry Pi Camera Connector - J9 | Raspberry Pi Camera Module 2 | Video | imx219_filesink |
| Raspberry Pi Camera Connector - J9 | Raspberry Pi Camera Module 2 | Video | imx219_perf |
| IAS Connector - J8 | AR1335 Sensor | Video | ar1335_filesink |
| IAS Connector - J8 | AR1335 Sensor | Video | ar1335_perf |
The BIST application requires the following hardware setup to run
the full suite of hardware tests:
* USB Flash Drive (x4)
Connect a USB Flash Drive to each of the four USB ports.
* Ethernet Cable (x1)
Connect an Ethernet cable from the Ethernet port on the KV260 to
the host machine.
* PMOD (x1)
Connect Test PMOD on J2 on the KV260. Connect the pins on PMOD as described below.
- Connect P1 to P7
- Connect P2 to P8
- Connect P3 to P9
- Connect P4 to P10
* Monitor
Before booting, connect a 1080P/4K monitor to the board via either Display Port and/or
HDMI port.
* AR1335 IAS-ISP Image Sensor Module
Connect the AR1335 Camera Sensor to J7/IAS0 on the KV260.
* AR1335 IAS-direct Image Sensor Module
Connect the AR1335 Camera Sensor to J8/IAS1 on the KV260.
* RaspberryPi Camera v2 module
Connect the Raspberry Pi Camera Module to J9 on the KV260.
* The following image shows a KV260 setup with all the hardware connected.
## Next Steps
* [Run the BIST Application](run.md)
Copyright © 2023 Advanced Micro Devices, Inc
Terms and Conditions